2024 New NACE-CIP2-001 Exam Questions Real NACE Dumps
Course 2024 NACE-CIP2-001 Test Prep Training Practice Exam Download
NACE-CIP2-001 exam is the second level of certification offered by the National Association of Corrosion Engineers (NACE) International. Coating Inspector Level 2 certification is designed for individuals who have already completed the Coating Inspector Level 1 certification and have gained practical experience in the coatings industry. NACE-CIP2-001 exam covers a wide range of topics, including surface preparation, coating application, inspection methods, and report writing.
NEW QUESTION # 41
NACE No.13/ SSPC 6 identifies the use of:
- A. Watterjetting only
- B. Steam cleaning only
- C. Abrasive blasting only
- D. Various methods of cleaning
Answer: D
NEW QUESTION # 42
In which type of concrete are laitance commonly encountered?
- A. Concrete block (poured with a form)
- B. Gunite
- C. Glass fiber cement
- D. Poured (wet cast)
Answer: D
NEW QUESTION # 43
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Check to See if the dehumidification equipment is operating correctly
- B. Document the readings at the end of the shift
- C. Advise the coating applicator supervisor of your readings
- D. Call your supervisor
Answer: C
NEW QUESTION # 44
When using a destructive Paint Inspection Gauge the NACE inspector must:
- A. Ensure the glue on the dolly is properly applied prior to use
- B. Determine the Dry Film Thickness of the coating prior to use
- C. Select the appropriate hand wheel based on the measured Dry Film Thickness prior to us
- D. Consult SSPC Guide 1 prior to use
Answer: B
NEW QUESTION # 45
Antifouling coatings are regulated by international treaties.
- A. True
- B. False
Answer: A
NEW QUESTION # 46
A single component water borne acrylic coating cures by:
- A. Oxidation
- B. Solvent Evaporation
- C. Co-Reaction
- D. Coalescence
Answer: D
NEW QUESTION # 47
Examples of non-ferrous metals include
Select All that Apply:
- A. mild steel.
- B. aluminum
- C. copper
- D. iron
Answer: B,C
NEW QUESTION # 48
As a NACE Level 2 Inspector on a field job; prior to submission your documentation should always reviewed and approved by:
- A. A NACE Level 1 Inspector
- B. Another NACE Level 2 Inspector
- C. A NACE Protective Coating Specialist
- D. A NACE Level 3 Inspector
Answer: D
NEW QUESTION # 49
Linings are used on the interior of pipelines to
- A. protect the transported product.
- B. provide protection against soil chemicals.
- C. reduce magnetic polarity.
- D. afford limited temperature insulation.
Answer: A
NEW QUESTION # 50
The most likely area of failure on a buried external pipeline coating is the:
- A. Field joint coating
- B. Mainline coating
- C. Areas exposed to Ultra Violet light
- D. Ground bed
Answer: A
NEW QUESTION # 51
Corrosion is the reverse process of
- A. galvanic deterioration.
- B. steel manufacturing.
- C. flaking.
- D. hot dipping.
Answer: B
NEW QUESTION # 52
You are the NACE Coating Inspector on a tank lining project and are asked to perform a high voltage holiday test after the coating applicators have completed their final repairs. After meeting all the confined space entry permit you enter the tank and notice a very strong odor of solvent.
Your first course of action should to:
- A. Exit the tank and document the incident in your daily report
- B. Don your air supplied respirator and continue the testing
- C. Exit the tank and immediately and report the problem to the nearest safety supervisor
- D. Investigate to find the source of the odor
Answer: C
NEW QUESTION # 53
When conducting inspections the Inspector should follow which standards:
- A. The specified standards
- B. NACE and SSPC standards in North America
- C. Australian standards in Australia
- D. ISO standards in Europe and Asia
Answer: A
NEW QUESTION # 54
The main reason dehumidification is used during coating operations is to
- A. allow the contractor to guarantee the completion date.
- B. control the environment
- C. reduce the possibility of missing the recoat window.
- D. avoid repetitive blasting/coating operations.
Answer: B
NEW QUESTION # 55
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. High-pressure water washing
- B. Sacking
- C. Stoning
- D. Acid etching
Answer: B
NEW QUESTION # 56
......
NACE-CIP2-001 (Coating Inspector Level 2) Exam is a widely recognized assessment in the field of corrosion prevention and control. NACE-CIP2-001 exam is designed to test the proficiency of professionals in the coating industry and validate their knowledge in the inspection, evaluation, and documentation of surface preparation and coating application. Successful completion of NACE-CIP2-001 exam grants the Coating Inspector Level 2 certification, which is highly valued in the industry.
NACE-CIP2-001 Exam Info and Free Practice Test Professional Quiz Study Materials: https://actualtests.vceprep.com/NACE-CIP2-001-latest-vce-prep.html